أرجو من جميع الاخوة المشاركة
((وانت شفيك طل من برة))
=
=
=
=
=
=
=
=
=
=
يـــــــــــاخوان ترى البيس تو الجديد فيه مشكلة و هي احتراق العدسة معدل او غير معدل
وقد بدات تظهر حلول مثل هذه القطعة
http://www.mod-chip.com/images/mfd_fix.jpg
فهل من تعليق
أرجو من جميع الاخوة المشاركة
((وانت شفيك طل من برة))
=
=
=
=
=
=
=
=
=
=
يـــــــــــاخوان ترى البيس تو الجديد فيه مشكلة و هي احتراق العدسة معدل او غير معدل
وقد بدات تظهر حلول مثل هذه القطعة
http://www.mod-chip.com/images/mfd_fix.jpg
فهل من تعليق
انا شريت البلايستيشن 2 الجديد الصغير ولعبت فيه ساعتين و تالي طلعت منه ريحة احتراق وقام ما يشغل أي شي و رحت المحل وبدله الحين له يومين مافي خراب هل في أحتمال يحترق مع العلم ان موديله pal scph-7000r cb
وجات معاه لعبة كرة أصلي made in china
وش أعمل عشان ما يحترق
طلبتكم يا شباب يرجى الرد بسرعة
نعم فيه احتمال كبير وذلك لان الجهاز حقك مش محمي عل الاقل بهذه القطعةhttp://www.mod-chip.com/images/mfd_fix.jpg
نعم لقد وجدت الحل بس يقولون انه مش كافي عل عموم أرجو ان نتناقش حوله
-----------------------------------------------------------------------------
Just a quick follow-up to our previous reports. A more in depth explanation will follow later on but at this
point we believe it's more important to offer a quick fix for all those poor pstwos out there ;-)
Further analysis on several V12 has shown that in certain situations the mechanics controller can fail while
communicating with the dvd controller.
You can notice when this happens since the reset button, which is connected to the mechanics controller,
will stop responding and the only way to turn off the machine is to unplug the power jack.
When the mechanics controller crashes, the dvd controller keeps sending a pulse train to the tracking and
focus drivers which results in a steady voltage increase on both the tracking and the focus coils.
With the proposed diode fix, this increase is initially limited but if the user leaves the crashed pstwo on for
several seconds the output drivers will eventually reach saturation and, if the RS2004FS thermal protection
doesn't kick in, the coils can burn from the increased current flowing.
As promised on our latest news, our proposed solution to this problem consists in a simple 12c508 plus
an additional resistor.
There are certainly other solutions to this problems (some of which are currently being tested) which
can offer a more general protection to the coils by constantly monitoring the voltage applied to them.
However we felt that it was much more important to offer a cheap, easy and fast fix instead of a more
general one which would be outside the reach of the general hobbyist.
In a few words : programming a 12c508 pic is something most people with interest in electronics can
easily do. The blank component is very cheap (around 1 USD) and a programmer can be built or bought
for a few bucks if needed.
Further more, this simple fix has been proven to work an all occasions during our tests, so it should
already offer a very high protection.
http://www.infinitymod.com/matrix/we...Prob/schsm.JPG
We are releasing the pic hex file free (as in speech and as in beer ;-) ) for all to use and experiment on.
We are also releasing the gerber files for two small PCBs : one can be used with only the pic and the
resistor, while the other has also space for 8 1n4148 smd diodes.
Do with those as you wish : make a few of them for you own use, or build some more and offer them for
sale (hopefully for a low price, since all the research and development cost has been already done ;-).
The simple program to be burned inside the 12c508 will constantly monitor the communication between
the mechanics controller and the dvd controller. As soon as it detects a crash in the communication it will
turn off the pstwo to avoid any possibile damage to the coils.
You can download the .zip file with the program and the PCB gerber files from HERE.
Important notes:
The resistor value (1500 Ohm) has been chosen as the best value according to our tests.
If the value is less than 1000ohm the pstwo will stay in a permanent reset state and not even the red led
will turn on.
On the other end if the value is higher than 3300 ohms the pic will not be able to turn off the pstwo when
needed. This has been tested on several machines with consistent behaviour.
However there might be other board revisions which might behave in a different way (maybe because of a
different reset controller IC used).
So if you experience problems with the 1500 Ohm resistor, you can probably safely increase it to 2000/2200
ohms. Please, only experiment with different values if you understand what has been said (or if you don't
care about running your pstwo without being sure that the coils protection is working).
The usual installation care should be used when installing this fix.
Preferred position for placing the pic or the PCB is in the lower left corner of the ps2 motherboard.
Make sure that both a J and K wires run parallel to the board and make them as short as possible.
Last words: this fix can be used with or without the diode fix.
The diode fix can certainly increase the life span of your lens, and should provide you with more time to
realize that your ps2 crashed and turn off the main power, should the pic chip fail to work. This has not
happened once so far in our test, but as usual the real results will come from the thousands of pstwos out
there.
اي سؤال انا حاضر
لعدم الدوار او الدوخة
روح للموقع التالي http://www.infinitymod.com/cgi-bin/matrix/site.pl
حيث ان الحل الي نقلته من قبل يمتل حل 12c508 رسستور ((بالعربي ؟؟؟؟؟؟))
اما الحل التني فهو حل الديود ((بالعربي ؟؟؟؟؟؟)) http://www.infinitymod.com/matrix/we...leFixSmall.GIF
الحل الاول يخلي البايستيشن يطفي عشان يتفادى الضرر !!!!!!!!!!!!!!
أرجو الردود = 150
تسلمون على الرد يا شباب بس انا ما افهم عنقريزي فهموني نقطة نقطة وش القطعة الي أركبها وكم قيمتها ؟ يعني عطوني تفاصيل أكثر وشكراً
بس صعب ولازم تسو((Programation)) للقطعةاقتباس:
المشاركة الأصلية كتبت بواسطة azpc
--والله يأخي انا محتار انت قلت شكرا عل الردود يا شباب :bigeyes: ويــــــــــــن:reporter: انت راجع من كتب الردود:reporter::31: وشوف لاني من أول قايل ان الموضوع يستاهل مناقشة والبحت عن حل لكن الشباب مش فاضيين هل الايام ((مع اني بكرى عندي امتحان:shock22: :vereymad: :33: واذا طلع صعب وما قدرت احله:bigeyes: :wow: :17: :boggled: ))
_أدعولي يا شباب عل الاقل_
يالله نشوفكم في الاجازة بعد اسبوع وان شاء الله اجبلكم الحل العربي الكامل والمضمون و النهائي
فلا تفقدو الامل يا مقتنين PStwo وانا واحد منكم عندي الجهاز+القطعة غير مركبة وقاعد ادور عل الحل _+_لاتنسوني بالدعاء_+_
ولا تنسو الوعد ((الالتقاء بعد الامتحانات)):icon6: كلها أسبوع:31: هاه شدو حيلكم:mad: :12: :reporter:
__________والسلام عليكم ورحمة الله تعالى وبركاته___________
Please
هل الجهاز الصيني لا تحترق عدسته ؟؟؟:p
بس في بعض أنواع البلاي ستيشن ماتنحرق العدسة بعد 3 او 4 ساعات طبعا الموجودة في السعودية
:reporter: :reporter: :reporter: :reporter: :reporter: :reporter: :12: :12: :12:
واشوفكم بعد الاختبارات بعد اسبوعين او 3اسابيع:jester:
تشاو بااااااااااااي
ياجماعة الخير ..
انا وبحكم خبرتي الطويلة لا اجد اي صحيح في هدا الكلام ..
والله ماقد حصلت عمرها معاي ..
وانا كل يوم اصلح اكثر من جهاز للزبائن ..
كل الموديلات اشتغلت عليها ..
بس اريد ان اعرفكم شي ..
طبعا بحكم خبرتي مع الاعضاء اللي يكتبوا لي لحل مشاكلهم في المنتدى..
انة المهندسين اللي عندكم نصابيين مرة ...
ويكون الجهاز فقط يحتاج شوية صيانة ويقولو انة العدسة انتهت..
الله يعينكم على الغش الي انتو عايشين فية ...
والسلام ختام
سلاام انا الحمدلله انة البليستيشن مالي على الاقل كل سنة ونص تقريبا يبالها تبديل عدسة هذا بعد من كثر ما العب كل يوم على الاقل ساعتين اقل شي هذا :p
كل واجد ويا حظة :p
:shock22: أهلا أهلا بك مرة ثانية مستر نورساقتباس:
المشاركة الأصلية كتبت بواسطة النورس المعلا
بس هذه الاشياء انا جبتها لاني متأكد منها
انت تعرف قصتي مع البلايستيشن الي تخرب وانت عارف ليش:cool: (انشا الله مانستني)فرحت واشتريت هاذا المصيبة انا للحين ما لعبة فيه((بس 5 دقايق))
رحت لاحد المنتديات الخاصة بالقطعة الي شتريتها ((DMS4 Pro)) شفت الناس كلها تشتكي
من احتراق العدسة ____________
واذا مو مصدقيني
روح الى:
http://www.infinitymod.com/cgi-bin/matrix/site.pl
http://vandrunen.net/gallery/PSTwo_v...urrent_Limiter
http://web02063.prolocation.net/phpB...pic.php?t=3371
و أرجو ان نتواصل .....