الى خبراء اللينوكس و السامبا

[leader_a2000]

تحيه و بعد
اخواني لدي مشكلة و هي اني نصبت سامبا على ردهات 7.2 و انا داخل root و من ثم عملت restart للجهاز و بعدها لم تعد x-windows تظهر اليا حيث فقط تعمل عند كتابه startx و حتى عند كتابتها يدخل على الشاشه و لكن لا يظهر شيء على ال disktop
ساعدونا يا اخوان و الله مشكله ازعجتني جدا و جعل الله ثوابكم ان يزيدكم علما و معرفه

[vip200x]

اخي leader_a2000 بعد التحيه

يبدو ان هناك ملفات انحذفت او حدث فيها خطأ معين

الحل هو وضع السيدي الي حملت منه اللينكس

وسو له up وسوف يعيد الملفات التالفه انشاء الله

ولك خالص التحيه.


vip200x@hotmail.com

[يونكسي]

اخوي اعتقد ان مشكلتك ليس لها اي علاقه بالسامبا و احتمال كبير ان يكون حلها هو نفسه المكتوب في الصفحة

http://groups.yahoo.com/group/Linux4me/message/23

[leader_a2000]

الاخوه يونيكسي و vip 200x
تاكدت من وجود id:5:initdefault ومع ذلك بقيت المشكله و من ثم عملت upgrade ممينوكس و النتيجه:




:" :" :" :" :"


تحطم النظام كامل و لم يعد يشتغل و ها انا الان اريد ازالة اللينوكس لتنزيله مرة اخرى و لا اعرف كيف خاصه انه عندي windows 2000 serevr &proffisional على نفس الجهاز و اعرف انه لو كان win98 لكان الامر سهل
و لكن مع هذه الانظمه اجد صعوبه فبالله عليكم اخرجوني من هذه الورطه اذا استطعتم

[Loner]

Samba allows Linux to access Windows files that are located on OTHER networked computers, or to make Linux act as a print/file server for other Windows computers.

I understand from your post, that you want to access Windows files that are located on the SAME copmuter. If that is the case, then you don't need Samba at all.

All you need is to add support for the filesystem used on Windows (fat, vfat, ntfs).

To quickly know what filesystems are supported on your system, type:

cat /etc/filesystems

Loner

[leader_a2000]

بارك الله فيك لكني ازلت linux و نزلته من جديد و الحقيقه انا اريد الويندوز الموجود على جهاز اخر لهذا استخدمت السامبا و مع ذلك واجهتني مشكله فانا اعرف الشكل التالي وهو
smbmount //winbox/c /mnt/win -U=WINUSER
ومع ذلك لا اعرف ما المقصود ب WINBOX او WINUSER
فاذا كان هناك اي معلومات لديكم تفيدونا فيها الله يبارك فيكم مع العلم انني قرات كتابه للاخ وليد في منتدى بوابة العرب لكن بدون توضيح كامل للمعاني السابقه او حتى ماذا نفعل بعد انتهاء التنصيب (تنصيب سامبا) هل ان الويندوز مباشره سوف يرى قرص اللينوكس ام ان هناك خطوات اخرى
و شكرا للاهتمام

[Loner]

Is Samba working now?

If it's not working, please send me the configuration file: smb.conf

Loner

[يونكسي]

السلام عليكم

جرب اخوي الصفحة هذي

http://ldp.isu.net.sa/HOWTO/SMB-HOWTO.html

[leader_a2000]

تحيه و بعد
هذا الملف اللذي يخص SAMBA على جهازي اي شخص لديه تعليق يرجى الكتابه و التوضيح مع الشكر


# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options (perhaps too
# many!) most of which are not shown in this example
#
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentry and a ; for parts of the config file that you
# may wish to enable
#
# NOTE: Whenever you modify this file you should run the command "testparm"
# to check that you have not made any basic syntactic errors.
#
#======================= Global Settings =====================================
[global]

# workgroup = NT-Domain-Name or Workgroup-Nam
workgroup = workgroup

# server string is the equivalent of the NT Description field
server string = Samba Server

# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
hosts allow = 192.33.20.12 192.168.2. 127.

# if you want to automatically load your printer list rather
# than setting them up individually then you'll need this
printcap name = /etc/printcap
load printers = yes

# It should not be necessary to spell out the print system type unless
# yours is non-standard. Currently supported print systems include:
# bsd, sysv, plp, lprng, aix, hpux, qnx
printing = lprng

# Uncomment this if you want a guest account, you must add this to /etc/passwd
# otherwise the user "nobody" is used
; guest account = pcguest

# this tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/%m.log

# Put a capping on the size of the log files (in Kb).
max log size = 1000

# Security mode. Most people will want user level security. See
# security_level.txt for details.
security = user

# Use password server option only with security = server
# The argument list may include:
# password server = My_PDC_Name [My_BDC_Name] [My_Next_BDC_Name]
# or to auto-locate the domain controller/s
# password server = *
; password server = <NT-Server-Name>

# Password Level allows matching of _n_ characters of the password for
# all combinations of upper and lower case.
; password level = 8
; username level = 8

# You may wish to use password encryption. Please read
# ENCRYPTION.txt, Win95.txt and WinNT.txt in the Samba documentation.
# Do not enable this option unless you have read those documents
encrypt passwords = yes
smb passwd file = /etc/samba/smbpasswd

# The following is needed to keep smbclient from spouting spurious errors
# when Samba is built with support for SSL.
; ssl CA certFile = /usr/share/ssl/certs/ca-bundle.crt

# The following are needed to allow password changing from Windows to
# update the Linux sytsem password also.
# NOTE: Use these with 'encrypt passwords' and 'smb passwd file' above.
# NOTE2: You do NOT need these to allow workstations to change only
# the encrypted SMB passwords. They allow the Unix password
# to be kept in sync with the SMB password.
unix password sync = Yes
passwd program = /usr/bin/passwd %u
passwd chat = *New*password* %n\n *Retype*new*password* %n\n *passwd:*all*authentication*tokens*updated*successfully*

# Unix users can map to different SMB User names
username map = /etc/samba/smbusers

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
include = /etc/samba/smb.conf.%m

# This parameter will control whether or not Samba should obey PAM's
# account and session management directives. The default behavior is
# to use PAM for clear text authentication only and to ignore any
# account or session management. Note that Samba always ignores PAM
# for authentication in the case of encrypt passwords = yes

; obey pam restrictions = yes

# Most people will find that this option gives better performance.
# See speed.txt and the manual pages for details
socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192

# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
; interfaces = 192.168.12.2/24 192.168.13.2/24

# Configure remote browse list synchronisation here
# request announcement to, or browse list sync from:
# a specific host or from / to a whole subnet (see below)
; remote browse sync = 192.168.3.25 192.168.5.255
# Cause this host to announce itself to local subnets here
; remote announce = 192.168.1.255 192.168.2.44

# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply
; local master = no

# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable
; os level = 33

# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job
; domain master = yes

# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election
; preferred master = yes

# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
; domain logons = yes

# if you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
; logon script = %m.bat
# run a specific logon batch file per username
; logon script = %U.bat

# Where to store roving profiles (only for Win95 and WinNT)
# %L substitutes for this servers netbios name, %U is username
# You must uncomment the [Profiles] share below
; logon path = \\%L\Profiles\%U

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
wins support = yes

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
wins server = w.x.y.z

# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one WINS Server on the network. The default is NO.
wins proxy = yes

# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The built-in default for versions 1.9.17 is yes,
# this has been changed in version 1.9.18 to no.
dns proxy = no

# Case Preservation can be handy - system default is _no_
# NOTE: These can be set on a per share basis
; preserve case = no
; short preserve case = no
# Default case is normally upper case for all DOS files
; default case = lower
# Be very careful with case sensitivity - it can break things!
; case sensitive = no

#============================ Share Definitions ==============================
[homes]
comment = Home
browseable = no
writable = yes
valid users = superuser
create mode = 0664
directory mode = 0775
# If you want users samba doesn't recognize to be mapped to a guest user
; map to guest = bad user


# Un-comment the following and create the netlogon directory for Domain Logons
; [netlogon]
; comment = Network Logon Service
; path = /usr/local/samba/lib/netlogon
; guest ok = yes
; writable = no
; share modes = no


# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
;[Profiles]
; path = /usr/local/samba/profiles
; browseable = no
; guest ok = yes


# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
comment = All Printers
path = /var/spool/samba
browseable = no
# Set public = yes to allow user 'guest account' to print
guest ok = no
writable = no
printable = yes

# This one is useful for people to share files
;[tmp]
; comment = Temporary file space
; path = /tmp
; read only = no
; public = yes

# A publicly accessible directory, but read only, except for people in
# the "staff" group
;[public]
; comment = Public Stuff
; path = /home/samba
; public = yes
; writable = yes
; printable = no
; write list = @staff

# Other examples.
#
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
; comment = Fred's Printer
; valid users = fred
; path = /home/fred
; printer = freds_printer
; public = no
; writable = no
; printable = yes

# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
; comment = Fred's Service
; path = /usr/somewhere/private
; valid users = fred
; public = no
; writable = yes
; printable = no

# a service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %U option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
; comment = PC Directories
; path = /usr/local/pc/%m
; public = no
; writable = yes

# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
; path = /usr/somewhere/else/public
; public = yes
; only guest = yes
; writable = yes
; printable = no

# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
;[myshare]
; comment = Mary's and Fred's stuff
; path = /usr/somewhere/shared
; valid users = mary fred
; public = no
; writable = yes
; printable = no
; create mask = 0765

[Loner]

Give me a couple of days and insha'allah I'll get back with you

Loner

[leader_a2000]

بارك الله فيك اخي loner والله انا مزعجك معي و اسأل الله لك علما نافعا وعمل متفبل وشفاء من كل داء

[Loner]

Samba is a complicated topic and I' know very little about it. Furthermore, I don't have anetwork to test Samba.

When you install Samba, you should install there RPMs (I'm talking about Red Hat 7.3):

samba-common-2.2.3a-6.i386.rpm
samba-2.2.3a-6.i386.rpm
samba-client-2.2.3a-6.i386.rpm

These 3 RPMs are the what you need to run Samba. You should also install:

samba-swat-2.2.3a-6.i386.rpm
and
apache-1.3.23-11.i386.rpm


Swat allows you to amdminister everything about Samba using an HTML Web page interface. Also, swat gives you help with all the items displayed. For swat to work, you need Apache Web Server.

I wish I can help more but I don't have the network hardware to test Samba.

Make sure to start samba, swat, and httpd services.

Good luck

Loner

[leader_a2000]

بارك الله فيك اخي loner و الله ما قصرت ان شاء الله احاول حسب تعليماتك وتنجح معي و سايقى احاول حتى تنجح معي و شكرا لك
و جزاك الله خيرا

[يونكسي]

اقول لك صراحة لو تطيع شوري كان ان شاء الله في يوم او يومين بالكثير كل شي راكب عندك بس مشكلتنا اننا نبي الشي جاهز ولا نحب نتعلم

جربت تقراء
http://ldp.isu.net.sa/HOWTO/SMB-HOWTO.html

؟؟؟؟؟؟